New Products List ｜SMC CORPORATION

[Dustproof and water-resistant] Ionizer / Bar Type　IZSW10 Series

New

Updated Nov-25

Dustproof and water-resistant (IP66 equivalent)
Ionizer unit can be washed.
∗ Static neutralization is not available while spraying with water.
Replaceable fittings
Air purge increases static neutralization distance by 3 times.
Select the ion generation mode for the application.
DC: Rapid static neutralization
Dual AC: Minimal uneven static neutralization

Blow Gun　VMG Series

New

Updated Nov-25

SMC “Blow gun” + “S coupler” + “Coil tube” + “Pulse blow unit” Max.60% reduction in CO₂ emissions when combined
With Pulse Blow Unit [New]
Intermittent pulse blow improves removal efficiency by 35% compared with continuous blow.
Available nozzles: Male thread nozzle (With cover) , Copper extension nozzle (With cover) , Low noise nozzle, High efficiency nozzle, Nozzle with flow rate adjustment function
Connection type: Screw, S coupler plug type, One-touch fitting type
Not affected by supply pressure, assured operability

Direct Operated/Pilot Operated 2-Port Solenoid Valve　JSX/JSX□ Series

New

Updated Oct-25

Water Hammer Relief JSXR Series has been added. [New]
Air Water, Oil, Steam, Heated, water, Vacuum
Improved environmental resistance due to the stainless steel coil cover
[IP67 enclosure/NEMA4X*] ∗ IP65 for models with a DIN terminal
CO₂ emissions (Power consumption): 71% reduction
Compact: Valve volume reduced by 25%*, Lightweight: Weight reduced
by 30%* ∗ Compared with the existing model
Energy saving
Coil force: 10% increase*, Power consumption: 14% reduction
(Compared with the existing model)
360° lead wire insertion and removal is possible.
Improved weather resistance in outdoor environments

Air Management System　AMS20X/30X/40X/60X-X2044/X2045 Series

New

Updated Oct-25

IO-Link compatible
Monitoring compressed air condition via IO-Link and reduction of air consumption
Standby regulator＋Digital flow switch
[Suffix: -X2044]
Operation mode ⇔ Standby mode
Digital flow switch＋Residual pressure relief 3-port solenoid valve (With soft start-up function)
[Suffix: -X2045]
Operation mode ⇔ Isolation mode

Clamp Cylinder with Lock　CLK2 Series

New

Updated Oct-25

Maintains a clamped or unclamped state when air supply pressure drops or residual pressure is released
Can be locked at any position within the entire stroke Locking is possible at any desired position.
Able to easily accommodate changes in workpiece thickness
Overall length: Max. 7 mm shorter, Weight: Max. 7% lighter
Able to maintain an unlocked state
Assembly and maintenance simplified
Various types of auto switches can be mounted.

Wireless System　EXW1/EX600-W Series

New

Updated Oct-25

Applicable to DIN rail mounting (A DIN rail adapter has been added.) to the compact type EXW1 series. [New]
Noise resistance
　Uses the 2.4 GHz ISM frequency band
　Frequency hopping: Every 2 ms (Fastest)
Communication cables not required
Reduced wiring work, space, and cost
Minimized disconnection risk
Provides communication stability in FA environments
Compact and lightweight (EXW1)
Volume: Approx. 81% reduction, Weight: Approx. 79% reduction

[Compatible with Manifold Controller] Electric Actuators　LE2S(H)/LE2F/LE2Y(G)/LE2R　Series

New

Updated Oct-25

Slide Tables LE2S(H)□H Series has been added. [New]
Compatible with manifold controller
Up to 16 axes can be connected
Annual CO₂ emissions reduced by up to 38% through motor control optimization (SMC comparison)
8.7 kg-CO₂e/year (14.1)
∗ The numerical values vary depending on the operating conditions.
Battery-less absolute encoder type
Restart from the last stop position is possible.

Pinch Valve/Air Operated Type　LPVA Series

New

Updated Sep-25

Easy tube replacement from front access
Removal together is possible. Max. 40% work time reduction
Compact, Lightweight
Small pitch mounting is possible.
With cover
Selectable port position according to the installation conditions
Tube size can be changed.

e-Actuator Easy to Operate Integrated Controller　Slider Type/Rod Type/Guide Rod Type　EQFS□H/EQY□H/EQYG□H Series

New

Updated Sep-25

An IO-Link type has been added. [New]
A guide rod type (EQYG□H series) has been added.
Communication cable with Push-Pull connector
Easy to set up, just like air equipment
Downsized with integrated controller, Wiring saving, Labor saving, Programless, Reduced adjustment time
Annual CO₂emissions reduced by up to 59% due to optimized motor control method (SMC comparison) [5.8 kg-CO₂e/year (14.1)] ∗ The numerical values vary depending on the operating conditions.

Angle Seat Valve / Air Operated Type　JSB Series

New

Updated Sep-25

A clamp connection type and a butt weld connection type have been added. [New]
Low pressure loss due to angle seat structure!
Long service life: 10 million cycles (Air, Water), 3 million cycles (Steam)
Large flow rate
A large flow rate is possible due to the optimized flow channel shape. (Cv factor: approx. 2.5 times)
Compact: Height 166 mm (Port size: 1")
All-in-One (Stainless steel 316L equivalent)
Air, Water, Steam

Solid State Auto Switch/Intrinsic Safety　D-M9BA□-917/-924/-925

New

Updated Sep-25

ATEX, UL/CSA, Japan explosion-proof
2-color indicator (Red, Green)
The proper operating range can be determined by the color of the light. (Red → Green ←Red)
Compatible with material restrictions for secondary battery manufacture

Magnetically Coupled Rodless Cylinder/Direct Mount Type　CY3R Series

New

Updated Sep-25

Improved lubrication
A Lube-retainer is installed to support lubrication retention on the piston and to ensure a lubrication film.
(Bore size: ø15 to ø63)
Stable operation
Lengthening of the wear ring on the body side by, 30% at maximum, helps to achieve smooth movement.
Improved piping flexibility
Improved piping flexibility with the addition of a right side centralized piping type
The specifications, magnet holding force, and mounting dimensions are the same as those of the existing CY3R series model.

Teaching Box for Electric Actuator　JX-T1 Series

New

Updated Sep-25

PC is not required.
Allows for electric actuator and controller data setting with a single unit
Compatible with stop switch units (option)
Operates on power supplied from the electric actuator/controller

Nozzle with flow rate adjustment function　KNC

Updated Aug-25

Flow rate can be adjusted at the most downstream side of the blow process.
Nozzle with male thread - Flow rate can be adjusted to ø2.0 equivalent or less.
Nozzle diameter: ø2.6
Nozzle with scale
Compatible fluid: Air

Safety Communication Fieldbus System　EX600 Series

Updated Aug-25

Safety/General purpose I/O integrated into one manifold
EtherNet/IP™, CIP Safety™
IEC 61508/IEC 62061 SIL3
ISO 13849 PL e
Safety/General purpose I/O modules can be connected.
Improving the efficiency of equipment startup and maintenance work
Simplified layout and reduced wiring

Mechanically Jointed Rodless Cylinder　MY1B Series

Updated Jul-25

Load mass: Max. 30% increase, Allowable moment: Max. 30% increase
* Compared with the existing MY1B
Same mounting dimensions as the existing MY1B

Micro Mist Separator with Pre-filter　AMH Series

Updated Jul-25

Pressure drop reduced by up to 50%. Contributes to energy saving
Easier replacement of the element. The clogging switch notifies when replacement is required.
Lightweight: Max. 50% lighter (Compared with the existing model)
Color-identifiable elements
Transparent bowl guard (2-layer construction)
The inside is visible from 360°.
The bowl is completely protected from the environment, allowing for improved safety.
Flow capacity increased by up to 50% （Compared with the existing model)

Compressed Air Preparation Filter/Stainless Steel Type　AFF□DS/AM□DS/AMD□DS Series

Updated Jul-25

Improved environmental resistance with the stainless steel exterior
Flow capacity: 14.5m³/min（ANR）
∗ For AFF90DS/AM90DS/AMD90DS
Pressure drop: 5 kPa or less
Easier replacement of the element
Compliant with ISO 8573 Compressed Air Purity Class

Air Grippers for Collaborative Robots　RMH□ Series

Updated Jul-25

Select from 3 types of tool changer.
Simple operation allows for easy tool changing.
Clamp type (Manual override),
One-push type (Manual override) [New],
Auto type [New], Tool holder [New]
Unitization of the peripheral devices required for gripper driving Operation is possible simply by connecting 1 air supply tube and 1 　electrical wire.
Built-in solenoid valve, exhaust throttle valve with silencer, auto switch, fitting, etc.
Can be used with the collaborative robots of 13 companies
UNIVERSAL ROBOTS, OMRON/TECHMAN ROBOT, FANUC, YASKAWA
Electric, Mitsubishi Electric, HAN’S ROBOT, KUKA, DOOSAN ROBOTICS,
SIASUN, JAKA, AUBO, ABB,
DENSO WAVE [New]
Air consumption reduced by up to 80%
Allows for temporary workpiece drop prevention
High rigidity and precision are achieved by integrating the guide and finger.
With high-precision linear guide

Air Servo Cylinder　IN-777

Updated Jul-25

Produced upon receipt of order

Capable of air cylinder multipoint positioning and control
Fast response and high positioning repeatability
Positioning repeatability: ±0.5 mm
Easier maintenance due to unitization
Built-in self-diagnosis function (LED lamp and signal output)
Emergency stop of the piston when the air or power supply is cut
Supports 4-20 mA/HART communication as the communication protocol
FOUNDATION Fieldbus communication has been added as a communication protocol. [New]

NAAMS Standards Compliant
Power Clamp Cylinder　CKZ5N Series

Updated Jul-25

Bore sizes ø80 has been added. [New]
A new structure has achieved downsizing.
Overall length reduced by 49 mm max.
Depth reduced by 17.3 mm max. (Interchangeable with existing product CKZ3N in terms of installation)
Weight reduced by up to 27%
Aluminum body with greatly reduced weight
High clamping force 4000 N (ø63, Arm length: 100 mm, 0.5 MPa)
Manual lock release operability has been improved.
Spatter-proof construction
　Fully enclosed structure by means of an aluminum body

Power Clamp Cylinder　CKZ5T Series

Updated Jul-25

Bore sizes ø40 and ø80 have been added. [New]
Weight reduced by up to 23%
Aluminum body with greatly reduced weight
A new structure has achieved downsizing.
Overall length reduced by 49 mm max.
Depth reduced by 17.3 mm max. (Interchangeable with existing product CKZ3T in terms of installation)
Weight reduced by up to 23%
Aluminum body with greatly reduced weight
High clamping force 4000 N (ø63, Arm length: 100 mm, 0.5 MPa)
Manual lock release operability has been improved.
Spatter-proof construction
Fully enclosed structure by means of an aluminum body

Refrigerated Air Dryer/For Use in North, Central and South America　IDFB□E Series

Updated Jul-25

Low GWP Refrigerant [New]
UL, CSA certified product
Power supply voltage: Single-phase 115 VAC (60 Hz), 230 VAC (60 Hz)
3-phase 460 VAC (60 Hz)
Note) The air flow capacity for each dew point is indicated.

∗ The IDFB22E/37E series has been discontinued in August 2019.
　Please select the IDFB60/70 series.

Refrigerated Air Dryer/For Use in North, Central and South America　IDFB Series

Updated Jul-25

Low GWP Refrigerant [New]
Applicable for the high-temperature environments
Ambient temperature: Max. 113°F (45°C)
Inlet air temperature: Max. 149°F (65°C)
Increased air flow capacity
Power supply voltage: Single-phase 230 VAC (60 Hz)

Stainless Steel Cylinder　CM5□ Series

Updated Jun-25

External parts made of stainless steel
Stainless steel is used for the cylinder body, mounting bracket, mounting bolt, and accessories.
Compact and lightweight (Compact type)
Overall length reduced by 21%* (175 mm→139 mm)
Weight: Max. 50% reduction* (0.75 kg→0.38 kg)
∗ Compared with the existing CG5-S series at 32 mm bore and 50 mm stroke
4 times or more life expectancy under the water droplet scattering environment*
(Improved water-resistant type)
∗ Compared to the standard CM2 product series
Grease for use in food machinery: NSF-H1 certified greases are available.
Seal material: FKM or NBR are available.

Compact 5-Port Solenoid Valve/Non Plug-in Type JSY1000/3000/5000 Series

Updated Jun-25

Non Plug-in Body Ported Single Unit (For Mounting P.E Plate)
A 3-position type has been added. [New]
Size reduction possible thanks to a flow increase
This leads to space saving, weight reduction, and a large flow rate.
Power consumption: 0.1 W (With power saving circuit), 0.4 W (Standard)
4-position dual 3-port valve available
Bottom ported is prepared (A, B port).
Manifold type no.: JJ5SY1, JJ5SY3, JJ5SY5
An M12 connector has been added. (JSY5000 only)

Remote Control Valve (Electric speed controller)　PFES Series

Updated Jun-25

The speed controller is equipped with a motor
Speed controller capable of “remote control” by “electrification”
Large reduction in equipment setup time and downtime
Easy maintenance
Reduced adjustable work-hours
Improved productivity
Reduced down time

ISO 13849-1 Certified Safe Exhaust Valve Modular Connection Type　VPX400 Series

Updated Jun-25

Double common specification has been added. [New]
Safety standard ISO 13849-1 compliant
(Corresponding to categories 3 and 4)
Exhaust flow rate characteristics [L/min (ANR)]　∗ At 0.6 MPa
10,500 (VPX406-A3)
13,000 (VPX406-A3)
15,000 (VPX406-A6)
Space saving & lightweight: 3 functions have been integrated.
Dual residual pressure release valve + Soft start-up valve + Main valve inconsistency detection
Modular connection is possible.
(AC30/40/50/60-D series)

Pulse Blow Unit　PU Series

Updated Jun-25

Intermittent pulse blow improves removal efficiency by 35% compared with continuous blow. (∗ Based on the test by SMC.)
CO₂ emissions (Air consumption): 50% reduction
Possible to adjust operating frequency
External power supply is unnecessary.
A pulse blow is possible by the air supply.
Low pressure loss is achieved.
A large effective area (10.3 mm²) helps reduce the air consumption.
Possible to use it with its bracket mounted
Combined use with a blow gun
Compact, Lightweight
Weight：47 g
Valve volume：59.4 mm×24mm×28mm

Modular Type Relief Valve　AP20-D Series

Updated Jun-25

Releases pressure over the set range into the atmosphere and constantly maintains the pressure in a pipe
Set pressure: 0.05 to 0.8 MPa
Modular connection is possible.
Reduced piping labor, Branch piping is not required.
Easy to handle
Selection of pressure gauges

Flow Controller for Water　FC3W Series

Updated Jun-25

IO-Link compatible [New]
Rated control flow rate range:
A 5 to 40 (L/min) specification has been added. [New]
For the stepless control of water flow rate in proportion to electrical signals
Flow rate control accuracy: ±5% F.S.
Response time: 10 s or less
Parts in contact with fluid: Grease-free

Suction Cup/With Non-slip Feature　ZP3M Series

Updated Jun-25

An oval bellows shape with non-slip feature has been added. [New]
Longer life (More than twice that of urethane cups)
Cup material: FS61 (Fluoro-based rubber) with excellent abrasion resistance
Reduced number of cup replacements
Non-slip special ribs
Diagonal ribs are radially arranged to secure the gripping force in all directions.
・Prevents workpiece slippage
・Secure adsorbing and transferring are possible.
Bowl shape with excellent flexibility
Curved workpieces can also be adsorbed.
The cup follows the workpiece shape, making stable adsorption possible.
Horizontal holding force: 387 N (Cup diameter ø100)
Suitable for high-temperature workpieces (200°C)
Suitable for workpieces with oil film
As oil is ejected to the grooves between special ribs, the lateral slipping of workpiece can be suppressed even on a steel plate with oil film.

Hygienic Design Cylinder　HYB/HDYB Series

Updated Jun-25

A water resistant cylinder configured for easy cleaning
Approx. 5 times increase in service life compared to the existing model (SMC ratio)
Grease for food processing equipment (NSF-H1 certified) is available.
External seal material: Choice of NBR or FKM

Air Cylinder Short Type　CG3/CDG3 Series

Updated Jun-25

Overall length Max. 51 mm shorter, Weight Max. 24% lighter (Comparison to CG1)
With auto switch (CDG3 series: CDG3)

Air Cylinder　CG1 Series

Updated Jun-25

A single acting type/A direct mount type/An end lock type has been added. [New]
Improved piping flexibility
Cylinder with rod end bracket is standardized.
Interchangeable in mounting with the existing model
Various mounting bracket options
Part numbers for products with a rod end bracket and/or a pivot bracket
It is not necessary to order a bracket for the applicable cylinder separately.

Mounting Kit for Multi-Axis System　LEA Series

Updated Jun-25

Creation of an XYZ unit
Easy system construction using the model selection software
Compatible actuators
X-Y-axis: LEFS series, LEFB series, LEKFS series
Z-axis: LEYG series
Compatible controllers/drivers (For single axis)

JXC51/61 series, JXC91/E1/P1/D1/L1/M1 series, LECS□‐T/LECY□ series

Exhaust Flow Control Valve with Silencer　ASN2□-A Series

Updated Jun-25

Integrated restrictor and silencer
Reduced assembly time and number of components
Push-lock type
Resin body: Weight reduced by up to 80%
The speed can be adjusted on the valve side.
A type with a compact indicator is available.
The flow rate can be controlled numerically.
Contributes to reduced setting errors and work hours by managing flow rate figures (indicator)

Digital Flow Switch for Large Flow　PF3A□H(-L) Series

Updated Jun-25

Applicable fluid: Air, N₂, Ar, CO₂ [New]
500 L/4000 L/8000 L types have been added to the modular type. [New]
The display range has been expanded. (1.5 times the rated flow range) [New]
Accumulated pulse conversion value: Select from 4 types based on the flow range [New]
Accumulated pulse width: Select a setting between 50 to 100 ms [New]
A wide range of flow measurement is possible with 1 product.
Supports the IO-Link communication protocol

Membrane Nitrogen Generator　IN778-1/IN778-2

Updated May-25

Nitrogen enriched air purification is easily possible with only a compressed air supply.
Nitrogen concentration: Max. 99.9 or more/ Outlet air flow rate: 20 L/min (ANR) ^∗
∗ Inlet air pressure: 0.7 MPa, Inlet air temperature 25°C
Compact and easy to use at point of use
No power supply required
No need for gas cylinder replacement
Modular connection type
Outlet side compressed air purity class (Humidity)"2" ^∗
∗ IFor IN778-1

Refrigerated Air Dryer/For Use in Europe, Asia and Oceania　IDFA□ Series

Updated May-25

Standard IDFA□E/□ Series
・IDFA3E～15E1
　　[For use in Europe] Low GWP refrigerant: R1234yf (HFO)
　　∗ Not available for air transport
　　[For use in Asia and Oceania] Refrigerant: R134a (HFC)
・IDFA60 to 90
　　[For use in Europe] Low GWP Refrigerant: R454C (HFC) [New]
　　∗ Not available for air transport
　　[For use in Asia and Oceania] Refrigerant: R410A (HFC)
Large Size IDFA□F Series
　　[For use in Europe] Low GWP Refrigerant: R454C (HFC) [New]
　　∗ Not available for air transport
　　[For use in Asia and Oceania] Refrigerant: R407C (HFC)
・Tolerant of high temperature environment !
　　Top of its class in the industry for the large air-cooled type
　　Ambient temperature 45°C at max.,
　　Inlet air temperature 60°C at max.
・Energy saving design
　　Exhaust heat reduced by 25% at max.
　　Ambient temperature increase suppressed
　　Employs a heat exchanger made of high corrosion-resistant
　　stainless steel

In-line Air Filter　ZFD Series

Updated Apr-25

Operating pressure range: −100 kPa to 0.5 MPa
Able to capture foreign matter in both vacuum adsorption and vacuum release directions.
Prevents foreign matter from scattering again
Space saving
Installation area: 41% reduction
Check valve enclosure
Flow order: Filter ➡ Check valve
Prevents foreign matter from getting caught in the check valve
Applicable tubing O.D.: ø4, ø6, ø8

Non F-Gas (CO₂ Refrigerant) Refrigerated Thermo-chiller　HRZC Series

Updated Apr-25

Non F-Gas
Uses CO₂ refrigerant (R744)
Greatly reduced GWP
Air transport possible
Eliminates the need to pay for F-Gas recovery & disposal
Eliminates the need for periodic inspections based on the Fluorocarbon Emissions Control Act (Japan)

Solid State Auto Switch UL/CSA Certified　D-M9□-551/918

Updated Apr-25

D-M9□-551：UL, CSA certified
D-M9□-918：UL, CSA certified + Compatible with material restrictions for secondary battery manufacture
Dimensions and Specifications: The same as those of the standard (general purpose) D-M9□ auto switch

Stainless Steel Cylinder/Non-adjustable Air Cushion Type　HF2A-CG5 Series

Updated Apr-25

Equipment for the Food Manufacturing Industry
All stainless steel specifications (External parts: Stainless steel 304)
4 times better durability in environments where it may come into contact with water droplets
Non-adjustable air cushion
Mounting interchangeability between the stainless steel cylinder, CG5-S series

Polyethylene Tubing　TX/TIX Series

Updated Apr-25

Excellent chemical and heat resistance
Using materials compliant with Japan Food Sanitation Act, US FDA, and Regulation (EU) No. 10/2011^∗1
∗1 Using materials posted in the positive list
Operating temperature range
Air, Inert gas: −45 to 80°C
Water: 0 to 80°C (No freezing)

Fieldbus System (Serial Transmission System)　EX600 Series

Updated Apr-25

An IO-Link unit compatible terminal unit (IO-Link device) has been added. [New]
Supports digital inputs/outputs, analog inputs/outputs, and IO-Link units
Self-diagnosis function
Web server function
Various connectors available
Up to 9 units can be connected. (Excludes SI units)

Wireless Auto Switch　IN574 Series

Updated Apr-25

Wireless power supply and communication for a completely wireless system.
Cable free
Zero risk of problems due to wire disconnection
Zero cable space and wiring work required
Zero switch failure due to cable deterioration
Battery-less (Wireless power supply / Using WPT)
Zero maintenance for battery replacement
In Japan, a radio station license is required to use a power transmitter (WPT station).
An application fee for opening a station and a radio wave usage fee are required.
This product can only be used in countries that comply with Radio Law (Japan, United States, Canada).
This product cannot be used in non-compliant countries.

Wireless System/Compact Wireless Base　EXW1-X10

Updated Apr-25

Pairing with wireless remote and various parameter settings without using IO Configurator.
∗ Configuration of IO-Link devices not included.

Fieldbus System (Serial Transmission System) EX260 Series

Updated Apr-25

CC-Link IE TSN [New] , Safety over EtherCAT® [New] compatible
Space-saving installation
IO-Link compatible
IP67
Drives up to 32 solenoids
Daisy-chain wiring communication
RJ45 communication connectors (X205)

3-Port Solenoid Valve Modular Type/Residual Pressure Release Valve　VP346E/546E/746E/946E Series

Updated Apr-25

Can be connected to F.R.L. units (AC-D series)
Allows for space saving and reduced piping labor.
Flow rate characteristics C［dm³（/ s·bar）］
VP346E：4.2
VP546E：7.5
VP746E：12.6
Effective area mm²
VP946E：234
A model with a soft start-up function is also available.
Power consumption: 0.35 W (Without light)
Features a check valve built into the pilot flow path
(Supports pilot pressure drops caused by pressure fluctuations on the inlet side)

Process Gas Equipment

Updated Mar-25

5 regulator/back pressure regulator models have been newly added.
19 diaphragm valve models have been newly added.

See Catalog

3-Screen Display High-Precision Digital Pressure Switch　ZSE20□(F)/ISE20□ Series

Updated Mar-25

A low differential pressure range type
has been added to the 20A series. [New]
An M12 connector type has been added.
A low pressure range type has been added.
Integrated R1/8 fitting with bottom wiring entry
Visualization of settings
Simple 3-step setting
Easy screen switching
It is possible to change the settings while checking the measured value.
Delay time:1.5 ms or less
IO-Link compatible

Air Saving Impact Blow Gun　IBG Series

Updated Mar-25

Various functions
Pulse function [New]
Adjuster function with indicator
Increased impact force due to higher peak pressure
Reduces air consumption and operation time
Application: It is capable of eliminating, in a short period of time, the dust, etc.,
that is difficult to remove with the existing blow gun.

Suction Cup　ZP3C Series

Updated Feb-25

Sizes ø20 and ø25 have been added for the 2.5-stage bellows type. [New]
Material: FS61 (Fluoro-based rubber) improves abrasion resistance
∗ More than 4 times the abrasion resistance of SMC's urethane suction cups
Reduced suction of foreign matter, such as paper particles, due to mesh filter
Can be replaced without tools
2.5-stage bellows type
Optional inner ring and retainer

Turn-lock Type All Resin Fitting　KY Series

Updated Feb-25

Prevents leakage due to insufficient tube insertion
Ensure secure tube insertion
Visibility of tube grip status is possible.
Grease-free
Fluid: Air, Nitrogen, Water, DI water (deionized water), Some chemicals
Operating temperature range: 0 to 80°C
All resin (Non-Metal) (except rubber)

Compact Position Sensor　D-MPG Series

Updated Feb-25

Detects the stroke position of compact actuators such as air grippers
Repeatability: 0.1 mm
Compact sensor head and separate teach unit
Same shape as the D-M9□ solid state auto switch
Analog output
Switch output
IO-Link compatible

ISO Standards (21287) Compact Cylinder　C55/CD55 Series

Updated Feb-25

Smooth cylinder (C55Y) has been added. [New]
Made of stainless steel (-XC6) has been added. [New]
With coil scraper (-XC35) has been added. [New]
Auto switch mounting groove: T-slot type (-X1439) has been added. [New]
Bore sizes ø12 and ø16 have been added. [New]
∗ These are not subject to ISO Standards (21287).
ISO Standards (21287)
1.8 times the anti-lateral load capacity
The allowable lateral load has been improved by changing the material of the bushing. (For ø20)
Increased the standard product's maximum stroke limit (to 300 mm)
Standardization of the double rod (C55W) type, smooth cylinder (C55Y), simple specials, and made-to-order options
Change of rod end shape (-XA□)
Heat-resistant cylinder (–10°C to 150°C) (-XB6)
Low-speed cylinder (5 to 50 mm/s) (-XB13)

Magnet Buffer　ZP3B□M Series

Updated Feb-25

A new nut material has been added. [New]
Stable buffer reaction force during stroke
Adsorbs workpieces with different heights, Reduces the impact applied to a workpiece
Low particle generation
No particle generation due to the friction of a spring (spring-less structure)
Non-rotating
Reduces rotation by 4-pole magnets
Copper and zinc-free
Compatible with secondary battery manufacturing processes

3-Screen Display PSE Sensor Set Up Tool　PSE-ST Series

Updated Jan-25

Selectable from 2 models of IO-Link compatible compact pressure switch
Connection sensor detection
Automatic range detection and display!
Simple copy function
Automatic range detection and display!
Simple 3-Step Setting
Mobile Battery Connection
Connect via mobile battery for easy set up in any location!

Valve Manifold Integrated with Ejector System JSY1000-E Series

Updated Jan-25

Spacer type ejector with High-noise reduction silencer (Selectable) [New]
A vacuum release flow adjustment unit has been added. [New]
Compact All-in-One Manifold
The devices have been integrated into one for applications in which an actuator and vacuum suction are used together.
EtherCAT®，IO-Link [New] , PROFINET® [New] ，EtherNet/IP™ [New] compatible
Wiring/Piping Saving through Use of All-in-One Manifold
Installation area: 64%reduction
Weight: 42%reduction
Energy Saving Function
CO₂emissions (Air consumption) : 90% reduction

Refrigerated Thermo-chiller　HRSC Series

Updated Jan-25

Air transport possible
Uses CO₂ refrigerant (R744)
Greatly reduced GWP
Eliminates the need to pay for F-Gas recovery & disposal
Eliminates the need for periodic inspections based on the Fluorocarbon Emissions Control Act (Japan)

Rotary Actuators　CRB/CDRB Series

Updated Jan-25

A double vane type has been added for sizes 10 to 40. [New]
Features a compact body with a built-in angle adjustment unit and
auto switch unit (Size: 20, 30, 40)
Overall length: 44% shorter, Weight: 48% lighter
Piping, wiring, and angle adjustment can be performed on the same side for easier mounting.
Easy-to-adjust start and end positions with the angle adjustment bolts
(as standard)
The position of the chamfered portion of the shaft can be easily checked using the rotating angle indicator. (Only for the CDRB with auto switch)
Each of the units below for the CRB2 series can be mounted to the CRB series.

Tool Changer/Auto Type　RMTA Series

Updated Jan-25

Robot hand tool automatic exchange
Standards: ISO9409-1 compliant
Support for direct mounting on collaborative robots
Robot and end tool connection/release
More compact as flanges are not required.
Direct mounting on collaborative robots eliminates the need for flanges and reduces design labor
Supports a work load of up to 20 kg (Work load: 5 kg, 10 kg, 20 kg)

Tool Changer One-push Type/Clamp Type　RMTM Series

Updated Jan-25

2 types of manual tool changers
One-push Type
Tools can be attached/removed by the push of a button (no tools required).
Work load: 10 kg
Repeatability: ±0.01 (Position reproducibility)
Clamp Type
Tools can be attached/removed by clamper bolts (2 pcs).
Work load: 20 kg
Repeatability: ±0.02 (Position reproducibility)
Standards: ISO9409-1-50-4-M6 compliant
Compatible with the flanges of most major collaborative robots
Compact, Lightweight

Circulating Fluid Temperature Controller Thermo-chiller Dual Channel Refrigerated Thermo-chiller for Lasers　HRL Series

Updated Jan-25

A water-cooled refrigeration type has been added to the HRL100/200 series. [New]
Temperatures for 2 fluid channel systems can
be controlled individually by one chiller.
Space saving, Reduced wiring
Footprint: 22% reduction
One power supply system for 2 channels
Energy saving
Power consumption reduced by 30%
Touch panel

Stainless Steel Throttle Valve with One-touch Fittings In-line Type　HF2B-ASG-□TV Series

Updated Jan-25

Improved corrosion/heat resistance with the all stainless steel exterior
Possible for use in environments such as high temperature,
water splashing, and where copper and zinc cannot be used
Material: Stainless steel 316　∗ FKM (Seal)
Max. operating temperature: 150°C
NSF H1 grease
Fluid: Air, Water, N₂
Equipment for the Food Manufacturing Industry　HF2B- Series

Vacuum Gripper System (Foam Type)　ZGS Series

Updated Jan-25

Foam size: 300 mm x 180 mm / 200 mm x 120 mm [New]
Suitable for the palletizing and depalletizing of corrugated cardboard, etc.
Ejector unit
Combines all functions required for adsorption
(Ejector, Supply valve/Release valve, Silencer, Pressure switch)
Can be used immediately by simply connecting 1 electrical cable and air piping
Compatible with the collaborative robots of 4 companies
UNIVERSAL ROBOTS, OMRON/TECHMAN ROBOT, FANUC, YASKAWA Electric
Lifting force
440 N (200 x 120) (At −63 kPa)
880 N (300 x 180) (At −63 kPa)
2144 N (400 x 240) (At −75 kPa)
IO-Link compatible
∗ Only for sizes 300 x 180 and 200 x 120

[Low GWP Refrigerant Chiller] Thermo-chiller/Rack Mount Type　HRRF Series

Updated Jan-25

Low GWP refrigerant chiller
GWP: 146^∗　∗ Regulation (EU) 2024/573, AIM Act 40 CFR Part 84
EU refrigerant regulations: GWP150 or more
US refrigerant regulations: GWP700 or more
California, US refrigerant regulations: GWP750 or more
Environmentally friendly R454C as refrigerant
(Not available for air transport)
Operable without the need to remove the unit from the rack
Front access: Simple to control, service, and maintain with all filters and drainage accessible via the front panel
Space saving: Multiple chillers can be mounted to a 19-inch rack.
Cooling capacity: 1.2/1.8 kW (60 Hz)
Temperature stability: ±0.1°C
Power supply: Single-phase 200 to 230 VAC (50/60 Hz)

[Low GWP Refrigerant Chiller] Thermo-chiller/Standard Type　HRSF Series

Updated Dec-24

Low GWP refrigerant chiller
GWP: 146^∗
∗ Regulation (EU) 2024/573, AIM Act 40 CFR Part 84
EU refrigerant regulations: GWP150 or more
US refrigerant regulations: GWP700 or more
California, US refrigerant regulations: GWP750 or more
Environmentally friendly R454C as refrigerant
(Not available for air transport)
Lightweight/Compact　Same width for all models: 377 mm
Temperature stability: ±0.1°C
Compatible with power supplies in Europe, Asia, Oceania, and North, Central, and South America
Single-phase 200 to 230 VAC (50/60 Hz)

Water Separator for Vacuum　AMJ-D Series

Updated Dec-24

Removes water droplets in the vacuum line
Prevents vacuum equipment failures
Weight: Max. 30% reduction (AMJ40-D: 0.42 kg b AMJ4000: 0.6 kg)
Water drop removal ratio: 99% or more
Better environmental resistance with 2-layer construction
The bowl is covered with a transparent bowl guard.
Superior visibility: 360°

Pin Clamp Cylinder Lateral Compact Type　C(L)KQ32-X3445

Updated Dec-24

Lateral Compact Type
Compact: Overall length: 94 mm shorter (183mm→89mm)^∗
Lightweight: Weight: 38% reduction (900g→560g)^∗
∗Compared with the existing product CKQG32-X2081, LOW type, without lock
Lock mechanism to prevent the dropping of workpieces during emergency stops
Various clamp arm positions and port positions are available.
Mountable on 2 surfaces

High Speed/High Frequency Cylinder　CM2/CQ2-X3423

Updated Dec-24

Maximum piston speed: 2500mm/s
Maximum operating frequency: 15Hz
Kinetic energy: 1.5 times (Compared with the standard product)
Reduced impact due to revision of cushion structure
Reduced weight of moving parts (piston rod, piston, etc.)

Resin Pilot Operated 2-Port Solenoid Valve　JSXN-X1

Updated Dec-24

Body material: High strength PA66
Piping type
・Socket
・Thread: Rc, NPT, G
Fluid*　*Fluids that will not corrode wetted parts
・Water
・Diluted pesticides
・Liquid fertilizer
A water hammer relief feature
Seal material: NBR, FKM, EPDM
Power consumption: 3 W

Magnet Gripper/3-Position Type ø32　MHM-X7776

Updated Dec-24

Allows for high-speed transfer
Prevents the accidental attraction of a second workpiece and allows for high-speed transfer.
Improved cycle time
Gripper mountable on 3 surfaces (Excludes the port side)
Stopper (scale) allows for holding force adjustment and improved visibility

[Low GWP Refrigerant Chiller] Thermo-chiller/Dual Channel Thermo-chiller for Lasers　HRLF Series

Updated Dec-24

Low GWP refrigerant chiller
GWP: 146^∗
∗ Regulation (EU) 2024/573, AIM Act 40 CFR Part 84
EU refrigerant regulations: GWP150 or more
US refrigerant regulations: GWP700 or more
California, US refrigerant regulations: GWP750 or more
Environmentally friendly R454C as refrigerant
(Not available for air transport)
Temperatures for 2 fluid channel systems can be controlled individually by one chiller.
Space saving, Reduced wiring
Touch panel
Numeric keypad inputs
Notice for alarms and maintenance
Temperature waveform can be displayed.

Lever Hand Valve　VHL Series

Updated Nov-24

Space saving, Easy to operate (Vertical type) 5-port lever valve
Weight reduction of up to 45%
∗ Comparison between VHL21□D-02□ and VH210-□02
Footprint reduced by 58%
VHL210D 3216.5 mm² ⬅ VH20□ 7750 mm²
Panel mounting internal height reduced by 18.6 mm
For panel mounting
∗ Comparison between VHL210D and the existing VH20□ model
Flow rate increased by 73%
∗ Comparison between VH211□-02□ and VH210-□02
(Flow rate characteristics 1 → 4/2 (P → A/B))
3 operation types

IO-Link Compatible 2 in 1 Auto Switch　D-MH2□ Series

Updated Nov-24

Outputs process data according to the actuator stroke position
A single switch can discriminate between max. 3 position points.
Discriminable resolution: ±0.1 mm　∗ Within the high-resolution range
Detection position setting can be done away from the actuator.
Process data output (–1000 to 1000)
Can also be used with the 2 in 1 auto switch single unit if there is an IO-Link master

Low Profile Air Gripper　MHF2 Series

Updated Nov-24

ø25 and ø32 have been added. [New]
High rigidity, Gripping point distance: Max. 170 mm (For ø32, at 0.4 MPa)
Height: Max. 66% reducti
Moment reduction when transferring workpieces
72.8 mm → 25 mm(Comparison with our MHZ2 Series equivalent gripping force products)
3 types of strokes available for each size
Short stroke, Medium stroke, Long stroke

Vacuum Manifold for Fieldbus System　ZKJ Series

Updated Nov-24

Vacuum pads and actuator driving can be
controlled with a single manifold [New]
Positive pressure unit
5-port solenoid valve [New]
Vacuum unit
Energy saving ejector Air consumption: 92% reduction
Fieldbus compatible
Space saving: Requires no separate input/output units
Reduced wiring time
Compatible protocols: PROFINET, IO-Link, EtherNet/IP, EtherCAT
Exhaust sealing function
Quick workpiece release
4 stations/8 stations/12 stations/16 stations manifold compatible

Ionizer / Bar Type　IZS51 Series

Updated Nov-24

High speed static neutralization: Fastest time 0.1 s
Space saving: Height 70 mm x Width 28 mm
Compact and flat body
Can be mounted in narrow spaces
Supports the IO-Link communication protocol
Low maintenance cartridge
Concentrating the air (for reducing emitter contamination)
around the emitter and the assisting air (for ion transfer)
Reduces dirt on the emitter, compared with the existing model
Valve unit option
For reduction in air consumption by stopping air purge during stand-by mode